Products
-
AA Power board
Get clean 3.3V regulated power from a single AA battery! The AA Power board is a neat board for generating 3.3V from a single AA battery (Alkaline or NiMh), sufficient to power a JeeNode, for...€3.50 - €14.50
-
Analog Plug
The Analog Plug is a small board containing the MCP3424 analog-to-digital converter with I2C bus interface. The ADC can take 4…240 samples per second, depending on resolution (12..18 bits). It has 4 differential input channels and supports...€3.00 - €13.00
-
ARM Chips
Economical ARM Cortex M0+ chips for your projects ! The LPC810 is an entry-level 32bit ARM Cortex M0+ architecture chip from NXP. The 8 pin, Dual In-line Package (DIP) is ideal for breadboarding and easy to solder PCB...€4.50 - €13.00
-
Assembly service
Maybe you don't like soldering. Maybe you're worried about not getting the hardware to work first time or don't want to solder that Radio "SMD" module. Perhaps one fully working unit as an example will...€5.00 - €15.00
-
ATmega328 with RF12demo
This is the ATmega328p chip by Atmel, with 32 Kbyte flash memory. This chip comes pre-loaded with the new OptiBoot 4.4 Arduino boot loader and the RF12demo sketch. The fuses are set for use with...€8.25
-
Bare ARM Blinker
A solderless pathway for exploring the ARM Cortex M0+ ! The Bare ARM Blinker is an entry-level introduction to building neat functions using the 32bit ARM Cortex M0+ chip architecture. Designed as a solderless starter kit for less experienced...€9.50 - €23.50
-
Battery holder
This lets you use JeeNodes with batteries. Either the 3- or 4-cell unit is fine, the 4-cell provides higher voltage/more mAh capacity. Depending on whether – and how well – sleep mode is implemented in...€3.00 - €4.00
-
Blink Plug
The Blink Plug is a small board with room for two LEDs and two push buttons. A simple software trick can be used to interface to both switches and LEDs using only two I/O pins....€3.00 - €4.50
-
Bridge Board
The Bridge Board v2 is an add-on which makes it very convenient to use a JeeNode (or a JeeNode USB, or a SMD Kit) alongside a solder-less breadboard, by bringing all pins out to the...€5.50 - €9.00
-
Carrier Board (v2)
The Carrier Board is a re-wiring option which sits between a JeeNode and its plugs. It has exactly the right size to fit snugly in a compact ABS plastic box, made from two identical, standard depth half-shells...€4.50 - €12.00
-
Carrier Card
The Carrier Card is an add-on for use with the Carrier Board, via which it connects to up to 19 I/O pins on a JeeNode or SMD Kit. The entire inner area is perforated with...€4.50 - €18.00
-
Coin Cells
Power your Real Time Clocks JeeNode Micro JeeNode Zero etc. with these branded Lithium - Manganese Dioxide 3V coin sized batteries. They are low self-discharge, intended for a light average current draw, achieving a shelf life of several years....€2.50 - €4.00
-
Color Measuring Plug
The Color Plug is a small board containing the TAOS TCS3414 digital light color sensor. This chip measures the color chromaticity and illuminance of ambient light with up to 16-bits of resolution. An array of 16 tiny photodiodes...€3.00 - €18.50
-
Compass Board
The Compass Board is a small board containing the HMC5883 3-axis compass module by Honewell. The chip can be configured to 8 different sensitivities, from 0.9 to 8 Gauss full-scale, with read-outs up to 160 times...€12.50
-
Current Source Plug
The Current Source Plug is a small board based on the AP8803 chip to provide a constant current to two independent sets of power LEDs of 350 mA or 700 mA. The two I/O pins...€3.50 - €19.00
-
Current Transformer (Clip-on)
This is a quality clip-on current transformer, suitable for the Parasitic Mains Current Sense project, described in the extensive JeeLabs Weblog series as the Micro Power Snitch (MPS). The device is well insulated from the mains potential in...€9.50 - €10.00
-
DC Motor Plug
The DC Motor Plug is a small board containing two H-bridges to drive a single stepper motor or two small DC motors. The board uses an I2C I/O expander to support the two motor drivers...€2.50 - €12.50
-
Dimmer Plug
The Dimmer Plug is a small board containing the PCA9635 16-channel PWM LED driver. This driver communicates directly over I2C. There is a “DimmerPlug” class in the JeeLib library to interface with this driver, to...€2.50 - €12.00
-
Educato Kit
The kits come with all the surface mount parts soldered on and tested. It’s an easy build which beginners might expect to take a bit over an hour and more experienced builders a little over...€28.50
-
Ether Card
The Ether Card is an add-on for the Carrier Board, which in turn is made to fit perfectly in a standard project box. It has three 6-pin headers on the side (only 8 pins on two of...€5.00 - €21.50
-
Expander Plug
The Expander Plug is a small board with 8 general-purpose digital I/O lines. Each of the lines can be configured individually as input (with optional 100 kΩ pull-ups) or as output. The 2×6-pin connection carries...€2.50 - €6.50
-
Extension cables
These 6-wire extension cables were custom-made to make it easier to hook up plugs to ports (and to each other). The color codes were chosen to match the port header pinouts: PWR = RED DIO...€7.50
-
Flash Board
The Flash Board is a small PCB which sits on top of a JeeNode or SMD Kit, turning it into an ISP programmer for ATmega and ATtiny chips. The board includes an 128 Kbyte EEPROM,...€3.00 - €14.00
-
Garage Parking Aid
More from the Bare ARM series of solderless projects - the Garage Parking Aid. This kit tracks the Garage Parking Aid ARM Cortex M0+ project documented in the JeeLabs weblog. The Full GPA Kit contains all the parts needed to...€19.50 - €33.50
-
Graphics Board
Display a range of fonts, symbols or graphs dynamically with the Graphics Board. Create a compact assembly that integrates a 64x128 graphic LCD with a JeeNode (or JeeNode USB, or SMD Kit). You can still...€5.00 - €25.00
-
Gravity (accelerometer) Plug
The g Plug (or Gravity Plug) is a small board containing a MEMS-based 3-axis accelerometer sensor from Bosch Sensortec. With a high (10 bits) resolution and an adjustable ±2/±4/±8g range (i.e. up to 64 LSB/g),...€2.50 - €18.00
-
Heading Board (discontinued)
This board is no longer in production, see the Compass Board for a high performanc 3-axis / single-port alternative. The Heading Board is a small board containing the HDPM01 compass module by HopeRF. For some reason, there...€2.50 - €17.00
-
Hopjes
The secret is out! The key to productive late-night debugging sessions is a delightful Dutch candy. These are the world-famous Rademaker's Haagsche Hopjes, long-lasting candies with a subtle taste of coffee. When those grey cells are...€2.50
-
Infrared Plug
The Infrared Plug is a small board which can send and receive modulated infrared signals, as commonly used by many remote controls and appliances around the house. The board uses a CMOS 555-timer chip to...€2.50 - €12.50
-
Input Plug
Due to high demand from the Summer Sale this item is now out of stock. If you order now, you will join a FIFO queue for the next batch expected mid-November. The Input Plug is...€2.50 - €12.00
-
JeeLink (v3c)
No more waiting! The new batch has cleared QA ready for immediate shipment. The JeeLink is a fully assembled and ready-to-use USB-type “stick” which plugs directly into a PC, Mac or USB hub. It contains Atmel’s ATmega328p...€27.50 - €32.50
-
JeeLink Classic
The JeeLink is a fully assembled and ready-to-use USB-type “stick” which plugs directly into a PC, Mac or USB hub. It contains Atmel’s ATmega328p AVR microprocessor, HopeRF’s RFM12B wireless radio module and a branded FT232R USB interface chip. The...€27.50 - €32.50
-
JeeNode Micro
The JeeNode Micro (v3) is the skinny younger brother of the JeeNode - 15 x 47 mm, and just 3.5 mm tall, from using a thin PCB and an extra-flat wireless module. The two ports (not four) of the...€3.50 - €119.50
-
JeeNode SMD (v1)
This is a JeeNode built with SMD parts. It contains Atmel’s ATmega328p AVR microcontroller and HopeRF’s RFM12B 868 MHz wireless radio module, and pins to connect to an USB BUB or other FTDI interface. The...€4.50 - €199.00
-
JeeNode USB
The JeeNode USB is complete with a built-in USB interface so it’s a great way to get started with JeeNodes. If you just want to prove out a concept, plug in a JeeNode USB –...€3.00 - €159.00
-
JeeNode Zero
Go Wireless with the new JeeNode Zero - an ARM M0⁺ based board with fully integrated radio opens up great new projects. These compact units have Mecrisp Forth and radio module drivers pre-installed - just connect up and...€14.00 - €49.50
-
JeeNode(v6)
Go Wireless with the JeeNode - a compact, Atmel chip board with integrated radio opens up great new projects. Compatible with the Arduino platform you can program under Windows, MacOS, or Linux using sketches created with the Arduino IDE....€5.00 - €159.00
-
JeePlug Pack
The JeePlug is a tiny board which can be used for prototyping and to “re-wire” connections between various headers and cables. There are 8 × 10 plated-through holes and pads, all the pads on the...€9.00 - €9.50
-
Large breadboard
These large solder-less breadboards make it easy to try out things hooked up to a JeeNode, and to build up elaborate electrical circuits with many components and ICs, particularly in combination with Wire jumpers. The...€7.50
-
LCD Plug
The LCD Plug is a small board containing an MCP23008 I/O expander which connects to most common 16-pin character LCD displays that use the HD44780 standard. The backlight can be turned off for greatly reduced...€3.50 - €25.50
-
LED Node (v2a)
The popular LED Node gives full spectrum control of 12-24V RGB LED strips over wireless ! The LED Node v2 combines a JeeNode with powerful MOSFET switches - its narrow (18 x 132 mm) form factor is a good in-line fit...€4.50 - €27.50
-
Lux Plug
The Lux Plug is a small board containing the TSL2561 light intensity sensor. This tiny sensor communicates directly over I2C. There is a “LuxPlug” class in the JeeLib library to interface with this sensor and...€2.50 - €11.00
-
Memory Plug
The Memory Plug is a small board with 1 to 4 EEPROM memory chips. With M24M01’s from STMicroelectronics, the board can have up to 512 Kbyte of memory (4x 1 Mbit). An I2C bus running...€2.50 - €17.00
-
Mini breadboard
These mini breadboards make it easy to try out things hooked up to a JeeNode, particularly in combination with Wire jumpers. The boards have a self-adhesive backing and 2x 17 rows of interconnected pins (5...€4.00
-
MOSFET Plug
The MOSFET Plug is a small board containing two high-power MOSFETs for switching loads at up to 5A @ 50V (this will require an extra heatsink). For use without heatsink, a maximum currrent of 1...€2.50 - €9.50
-
Opto-coupler Plug
The Opto-coupler Plug is a small board containing a dual opto-coupler. It can be used to detect the presence of low DC voltages (a few dozen volts) and currents (milliamps) without creating a direct electrical connection...€3.00 - €8.50
-
Output Plug
The Output Plug is a small board containing an 8-bit I/O expander plus NPN darlington array. Each pin can sink up to 500 mA @ 50V. Clamping diodes are included, so that relays and small...€2.50 - €8.50
-
Plug Headers
The Plug Headers set contains ten 6-pin female 0.1" pin headers and ten 6-pin male 0.1" pin headers. These headers are used everywhere by JeeNodes and Plugs, as well as for the FTDI and PWR/SER/I2C connectors....€6.00
-
Plug Shield
The Plug Shield allows using I2C-based JeePlugs with any Arduino or compatible clone. It acts as interface between the hardware I2C port and the plugs. There is a level converter on board, as well as...€4.50 - €14.50
-
Precision RTC Plug
The Precision RTC Plug is a small (21x35mm) board containing a low power real-time clock with battery backup. It continues to track the time with second by second resolution while the attached node is sleeping or...€3.50 - €14.00
-
Pressure Plug
The Pressure Plug is a small board containing the BMP085 barometric pressure and temperature sensor. This tiny sensor communicates directly over I2C. Some processing is required to arrive at properly adjusted readings, this is available...€2.50 - €18.00
-
Project Boxes
These are sturdy, general purpose ABS plastic boxes. The clam-shell halves of the box match and mate together with a secure click. For flexibility, there are two stock shell sizes and either size may be used to form boxes...€4.00 - €5.00
-
Proto Board
The Proto Board is a small add-on board which fits over all the connectors of a JeeNode (except the FTDI connector). The two “ends” of the board are slightly different to help identify the proper...€3.50 - €30.00
-
Proximity Plug
The Proximity Plug is a small board which uses the MPR084 to support up to 8 capacitive input ("touch") switches. A solder jumper allows using up to two of these plugs on a single port....€2.50 - €9.50
-
RBBB
The Really Bare Bones Board (RBBB) is a mini board designed for those experimental applications that require small processors, such as wearable computing, prototyping, artist’s projects or any use for a low-cost, well-supported microcontroller. As...€1.50 - €17.50
-
RBBB Combo Pack
This package combines the USB BUB-II, with the popular Really Bare Bones Board (RBBB). Now you can upload sketches from your programming environment directly into the AtMega chip's EEPROM and provide it power from a USB port....€29.50
-
RBBB Combo Pack III
This package combines the USB BUB-III, with the popular Really Bare Bones Board (RBBB). Now you can upload sketches from your programming environment directly into the AtMega chip's EEPROM and provide it power from a USB port....€27.50
-
RBBB Pro
The Really Bare Bones Board (RBBB) is a mini board designed for those experimental applications that require small processors, such as wearable computing, near space experiments, toy prototyping, artist’s projects or any use for a...€18.00
-
Relay Plug
The Relay Plug is a small board containing two miniature relays, rated up to 3A @ 250V (both AC and DC). This plug is designed to switch low voltage, low power lights, motors, fans etc....€2.50 - €15.00
-
RFM12B 433 MHz
The RFM12B radio module by HopeRF is a small wireless radio module for sending and receiving packets on the 433 MHz ISM band using FSK. There are two variants, the -S1 series with a metal can...€6.50 - €29.50
-
RFM12B 868 MHz
The RFM12B radio module by HopeRF is a compact wireless radio module for sending and receiving packets on the 868 MHz ISM band using FSK. There are two variants, the -S1 series with a metal...€5.50 - €29.50
-
RFM12B Board
The RFM12B Board is a compact breakout board for HopeRF's RFM12B radio module, as featured on all JeeNodes and JeeLinks. If you are looking for an affordable way to add wireless communication to your Arduino...€3.50 - €62.50
-
RFM69CW Board
Here's a neat HopeRF RFM69CW radio module breakout board. An affordable choice to add modern wireless capability to your Arduino (original or compatible). Supporting both 5V and 3.3V power, this matches a whole range of Arduino...€3.50 - €115.00
-
RFM69CW Radio
The more recent RFM69CW radio module by HopeRF is a compact, powerful radio transceiver module for swapping data packets in the 868 MHz ISM band, using standard and enhanced FSK modulation. Great for sub-compact designs; just 4mm...€6.50 - €31.50
-
RFM95W / RFM96W Radio
LoRa™ is here! The innovative RFM95W / RFM96W radio transceiver modules by HopeRF build on the strengths of the RFM69 series by adding support for the LoRa™ PHY modulation method. This spread-spectrum technique can communicate even when signals are buried in the background noise,...€9.50 - €18.50
-
Right-Angled Plug Headers
This Plug Headers set contains ten 6-pin female 0.1" pin headers and ten 6-pin male 0.1" pin headers with the shorter legs conveniently pre-formed into a 90 degree bend. These headers are used everywhere by...€6.50
-
Room Board
The Room Board is a small board with sensors for indoor monitoring of several environmental parameters: temperature – via either an HYT131 or a DS18B20 humidity – via the same HYT131 sensor motion – via...€1.50 - €39.00
-
RTC Plug
The RTC Plug is a small board containing a low power real-time clock with battery backup. It continues to track the time with second by second resolution while the attached node is sleeping (or even powered...€2.50 - €8.50
-
SMD Kit (v1)
The SMD Kit is a tiny board with the ATmega328p microprocessor. It is compatible with the Arduino platform and can be programmed under Windows, Mac OS X, or Linux using sketches created with the Arduino IDE. The...€3.00 - €12.00
-
Special Request
This is not a product, but a way to pay for something which is not directly available in the shop. It can also be merged with an existing order to make changes or upgrades. Please...€1.00 - €7.50
-
Special Shipment
This is not a product, but a way to pay for upgrading the method of shipping your order. It can be used for Courier Services, Extra Insurance, Special Delivery Instructions etc. Please get in touch...€1.00 - €12.50
-
Stacking Headers
These stacking headers let you extend a board on top of existing headers, while allowing a next level to "stack" on top. Perfect for JeeNode ports (6-pin) and for the PSIX header (8-pin). They are...€6.00 - €6.50
-
Thermo Plug
The Thermo Plug is a small, versatile board with room for one of three types of temperature sensors, and either a buzzer or a transistor driver for a modest load such as relay, small motor,...€3.50 - €39.00
-
UART Plug
The UART Plug contains a hardware serial port with 64-byte buffers for both send and receive. It can support baudrates up to 115200 baud, if the connecting bus can handle this bandwidth. An I2C bus...€2.50 - €11.00
-
USB BUB II
The USB BUB-II board is a flexible active USB connector with many applications. It uses a branded FT232R chip, not a clone. This board has features not found on some other USB boards. A polyfuse to...€14.50 - €15.50
-
USB BUB III
Jeenode Zero ready: The USB BUB-III board is a flexible active USB connector. It uses a branded FT231X chip to convert USB traffic to serial, including important control signals. It appears as a virtual "COM" port...€12.50
-
USB power adapter
The USB power adapter is a power supply which delivers 5V to power your projects (or any other USB devices, for that matter). This adapter is extremely compact, yet very efficient. It can supply up to...€9.50 - €13.50
-
Utility Plug
The Utility Plug is a small board to interface any of the ports on a JeeNode to an RJ-12 jack. The kit includes the following extra components, to handle a variety of simple interfacing and...€3.50 - €14.00
-
Wind Sensor Rev C
No more waiting! The latest batch passed QA and cleared the backlog. A compact anemometer sensitive enough to detect human breath. Based on the time-proven "hot-wire" method, this technique excels at low to medium wind speed. Great for...€32.00
-
Wind Sensor Rev P
Due to heavy demand, there is no stock available at the moment. Ordering now will join the FIFO queue for new stock going into QA mid-June. A compact anemometer sensitive enough to detect human breath....€55.00
-
Wire Cutters
Give your prototyping a neater finish with these 110mm diagonal wire cutters. The sharp, compact cutting head with spring-loaded precision box joint works great for trimming component leads and light gauge copper wires. These are branded (DURATOOL...€9.50
-
Wire Jumpers
These jumper cables are great for quick prototyping, especially in combination with the Mini breadboard. The cables are flexible, with a convenient little grip and solid cores on both ends. A bundle contains over 50...€6.00