Skip to navigation.


Jee Labs

  • AA Power board

    Get clean 3.3V regulated power from a single AA battery! The AA Power board is a neat board for generating 3.3V from a single AA battery (Alkaline or NiMh), sufficient to power a JeeNode, for...

    €3.50 - €14.50

  • Assembly service

    Maybe you don't like soldering. Maybe you're worried about not getting the hardware to work first time or don't want to solder that Radio "SMD" module. Perhaps one fully working unit as an example will...

    €5.00 - €15.00

  • Bridge Board

    The Bridge Board v2 is an add-on which makes it very convenient to use a JeeNode (or a JeeNode USB, or a SMD Kit) alongside a solder-less breadboard, by bringing all pins out to the...

    €5.50 - €9.00

  • Carrier Card

    The Carrier Card is an add-on for use with the Carrier Board, via which it connects to up to 19 I/O pins on a JeeNode or SMD Kit. The entire inner area is perforated with...

    €4.50 - €18.00

  • Current Source Plug

    The Current Source Plug is a small board based on the AP8803 chip to provide a constant current to two independent sets of power LEDs of 350 mA or 700 mA. The two I/O pins...

    €3.50 - €19.00

  • DC Motor Plug

    The DC Motor Plug is a small board containing two H-bridges to drive a single stepper motor or two small DC motors.  The board uses an I2C I/O expander to support the two motor drivers...

    €2.50 - €12.50

  • Ether Card

    The Ether Card is an add-on for the Carrier Board, which in turn is made to fit perfectly in a standard project box. It has three 6-pin headers on the side (only 8 pins on two of...

    €5.00 - €21.50

  • Graphics Board

    Display a range of fonts, symbols or graphs dynamically with the Graphics Board. Create a compact assembly that integrates a 64x128 graphic LCD with a JeeNode (or JeeNode USB, or SMD Kit). You can still...

    €5.00 - €25.00

  • Heading Board (discontinued)

    This board is no longer in production, see the Compass Board for a high performanc 3-axis / single-port alternative. The Heading Board is a small board containing the HDPM01 compass module by HopeRF. For some reason, there...

    €2.50 - €17.00

  • Infrared Plug

    The Infrared Plug is a small board which can send and receive modulated infrared signals, as commonly used by many remote controls and appliances around the house. The board uses a CMOS 555-timer chip to...

    €2.50 - €12.50

  • JeeNode Zero

    Go Wireless with the new JeeNode Zero - an ARM M0⁺ based board with fully integrated radio opens up great new projects. These compact units have Mecrisp Forth and radio module drivers pre-installed - just connect up and...

    €14.00 - €49.50

  • JeeNode(v6)

    Go Wireless with the JeeNode - a compact, Atmel chip board with integrated radio opens up great new projects. Compatible with the Arduino platform you can  program under Windows, MacOS, or Linux using sketches created with the Arduino IDE....

    €5.00 - €159.00

  • JeePlug Pack

    The JeePlug is a tiny board which can be used for prototyping and to “re-wire” connections between various headers and cables. There are 8 × 10 plated-through holes and pads, all the pads on the...

    €9.00 - €9.50

  • LED Node (v2a)

    The popular LED Node gives full spectrum control of 12-24V RGB LED strips over wireless ! The LED Node v2 combines a JeeNode with powerful MOSFET switches - its narrow (18 x 132 mm) form factor is a good in-line fit...

    €4.50 - €27.50

  • MOSFET Plug

    The MOSFET Plug is a small board containing two high-power MOSFETs for switching loads at up to 5A @ 50V (this will require an extra heatsink). For use without heatsink, a maximum currrent of 1...

    €2.50 - €9.50

  • Opto-coupler Plug

    The Opto-coupler Plug is a small board containing a dual opto-coupler. It can be used to detect the presence of low DC voltages (a few dozen volts) and currents (milliamps) without creating a direct electrical connection...

    €3.00 - €8.50

  • Proximity Plug

    The Proximity Plug is a small board which uses the MPR084 to support up to 8 capacitive input ("touch") switches. A solder jumper allows using up to two of these plugs on a single port....

    €2.50 - €9.50

  • Relay Plug

    The Relay Plug is a small board containing two miniature relays, rated up to 3A @ 250V (both AC and DC). This plug is designed to switch low voltage, low power lights, motors, fans etc....

    €2.50 - €15.00

  • Stacking Headers

    These stacking headers let you extend a board on top of existing headers, while allowing a next level to "stack" on top. Perfect for JeeNode ports (6-pin) and for the PSIX header (8-pin). They are...

    €6.00 - €6.50

  • Utility Plug

    The Utility Plug is a small board to interface any of the ports on a JeeNode to an RJ-12 jack. The kit includes the following extra components, to handle a variety of simple interfacing and...

    €3.50 - €14.00

  • Wire Jumpers

    These jumper cables are great for quick prototyping, especially in combination with the Mini breadboard. The cables are flexible, with a convenient little grip and solid cores on both ends. A bundle contains over 50...

    €6.00