interface
-
Bridge Board
The Bridge Board v2 is an add-on which makes it very convenient to use a JeeNode (or a JeeNode USB, or a SMD Kit) alongside a solder-less breadboard, by bringing all pins out to the...€5.50 - €9.00
-
Carrier Board (v2)
The Carrier Board is a re-wiring option which sits between a JeeNode and its plugs. It has exactly the right size to fit snugly in a compact ABS plastic box, made from two identical, standard depth half-shells...€4.50 - €12.00
-
Carrier Card
The Carrier Card is an add-on for use with the Carrier Board, via which it connects to up to 19 I/O pins on a JeeNode or SMD Kit. The entire inner area is perforated with...€4.50 - €18.00
-
Ether Card
The Ether Card is an add-on for the Carrier Board, which in turn is made to fit perfectly in a standard project box. It has three 6-pin headers on the side (only 8 pins on two of...€5.00 - €21.50
-
Extension cables
These 6-wire extension cables were custom-made to make it easier to hook up plugs to ports (and to each other). The color codes were chosen to match the port header pinouts: PWR = RED DIO...€7.50
-
Graphics Board
Display a range of fonts, symbols or graphs dynamically with the Graphics Board. Create a compact assembly that integrates a 64x128 graphic LCD with a JeeNode (or JeeNode USB, or SMD Kit). You can still...€5.00 - €25.00
-
JeePlug Pack
The JeePlug is a tiny board which can be used for prototyping and to “re-wire” connections between various headers and cables. There are 8 × 10 plated-through holes and pads, all the pads on the...€9.00 - €9.50
-
Large breadboard
These large solder-less breadboards make it easy to try out things hooked up to a JeeNode, and to build up elaborate electrical circuits with many components and ICs, particularly in combination with Wire jumpers. The...€7.50
-
Mini breadboard
These mini breadboards make it easy to try out things hooked up to a JeeNode, particularly in combination with Wire jumpers. The boards have a self-adhesive backing and 2x 17 rows of interconnected pins (5...€4.00
-
Plug Headers
The Plug Headers set contains ten 6-pin female 0.1" pin headers and ten 6-pin male 0.1" pin headers. These headers are used everywhere by JeeNodes and Plugs, as well as for the FTDI and PWR/SER/I2C connectors....€6.00
-
Plug Shield
The Plug Shield allows using I2C-based JeePlugs with any Arduino or compatible clone. It acts as interface between the hardware I2C port and the plugs. There is a level converter on board, as well as...€4.50 - €14.50
-
Project Boxes
These are sturdy, general purpose ABS plastic boxes. The clam-shell halves of the box match and mate together with a secure click. For flexibility, there are two stock shell sizes and either size may be used to form boxes...€4.00 - €5.00
-
Right-Angled Plug Headers
This Plug Headers set contains ten 6-pin female 0.1" pin headers and ten 6-pin male 0.1" pin headers with the shorter legs conveniently pre-formed into a 90 degree bend. These headers are used everywhere by...€6.50
-
Stacking Headers
These stacking headers let you extend a board on top of existing headers, while allowing a next level to "stack" on top. Perfect for JeeNode ports (6-pin) and for the PSIX header (8-pin). They are...€6.00 - €6.50
-
USB BUB II
The USB BUB-II board is a flexible active USB connector with many applications. It uses a branded FT232R chip, not a clone. This board has features not found on some other USB boards. A polyfuse to...€14.50 - €15.50
-
USB BUB III
Jeenode Zero ready: The USB BUB-III board is a flexible active USB connector. It uses a branded FT231X chip to convert USB traffic to serial, including important control signals. It appears as a virtual "COM" port...€12.50
-
Wire Jumpers
These jumper cables are great for quick prototyping, especially in combination with the Mini breadboard. The cables are flexible, with a convenient little grip and solid cores on both ends. A bundle contains over 50...€6.00
